Equipment
-
$129.95Dual Pressure MK4 Regulator - Type 30 - 8mm x FFL duotights included
Need to set two different CO2 pressures for different beers on tap? Then you'll need two regulators to do it properly. With this MK4 Dual Pressure Regulator you'll be able to screw it into your CO2 bottle and fire away with two different pressures. No need to removing the High Pressure gauge off one regulator, buying an attachment and joining the two together.
See - Single CO2 Regulator - MK4 for the single version of this regulator.Out of Stock -
$19.95SodaStream CO2 Adapter - Deluxe With Pin Adjustment
Unlike our cheaper sodastream cylinder adaptors, this adapter has the added advantage that you can use the side thumb screw to depress the pin in the middle of the adaptor. This pin adjustment makes the sodastream cylinder adaptor significantly easier to use.
-
$19.95SodaStream Cylinder Filling Adapter with Bleed Valve
This easy to use SodaStream Cylinder Filling Adaptor will enable you to fill your own CO2 from your larger bulk cylinder into smaller SodaStream cylinders. An easy and inexpensive way to fill your own Sodastream Cylinders at home at a fraction of the cost of getting the refills from your local store.
See this video for full instructions: https://www.youtube.com/watch?v=MeopdQRJPTA
-
$59.95Disposable Nitrogen bottle
High Capacity Disposable Nitrogen (N2) Gas Cylinder - 1.43L - 110Bar.
Out of Stock -
$16.95Drip Tray - Plastic 30cm
A plastic drip tray for your beer taps with removable grill.
Material: Food Grade Polycarbonate
Colour: Black
Dimensions: approx. 30cm x 16cm
From: Krome Dispense -
$19.95Hop Tube - Stainless Steel with Chain
This Hop Tube is made from 304 stainless steel and is ideal for addling larger amounts of hop pellets, flowers or spices to your RoboBrew / BrewZilla without blocking the pump. It can also be used in your Brewhouse Kettle/Boiler, 19L corny keg, and the FermZilla. It cannot fit in a standard 50L Keg as the opening is not wide enough. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers. It will hold approximately 150g of hop pellets, allowing for some space to permit full extraction of the hop oils. Ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung from the keg lid or side of the vessel.
Diameter: approx. 66mm Heigh: approx. 300 mm.
-
$54.95Kegerator Cover - Water Resistant (for Series 4 and X Kegerators)
The Kegarator Cover is an ideal solution for storing your Kegerator outside or exposed to water/dust or dirt. Keep your Kegerator in the best condition you can.
Suitable for all Series 4 and Series X tap configurations.
-
$19.00Gas Ball Lock Post with 5/8" Thread for keg coupler
Gas Ball Lock Post with 5/8" Thread. These are a very popular accessory that allows you to convert a commercial keg coupler with 5/8" thread to a standard corny disconnect gas post. This is the simplest way to allow you to serve beer from commercial kegs in a standard homebrew kegerator or keezer without modifying your beer and gas lines.
-
$20.00Liquid Ball Lock Post with 5/8 Thread for keg coupler
Liquid Ball Lock Post with 5/8" Thread. These are a very popular accessory that allows you to convert a commercial keg coupler with 5/8" thread to a standard corny disconnect liquid post. This is the simplest way to allow you to serve beer from commercial kegs in a standard homebrew kegerator or keezer without modifying your beer and gas lines.
-
$20.00Gas Ball Lock Post with 1/4 Inch Bulkhead Assembly
These ball lock posts include a 1/4 inch BSP thread so you can attach it to a wide range of other fittings.
The posts include a 20mm long thread, an o-ring, poppet, locking nut and short dip tube. This would enable you to make a keg out of any pressure vessel if you wanted to. The assembly can also be fitted to regulators, gas manifolds and various other items.
Both Gas and Liquid posts available.
From: Kegland
