Fermenters
-
$64.95Temp Twister Cooling/Heating Coil for FermZilla
The Temp Twister allows you to heat and cool your FermZilla or other fermenter or bright tank, ideally by combining with a glycol chiller.
This coil can be adapted to fit any fermenter or bright tank that has an opening of 110mm diameter or larger. Simply drill to two 22mm holes in the lid of your fermenter and use the included Duotight bulkhead fittings to attach the coil to the lid of your fermenter.
-
$89.95FTSs Quick Connect Kit
The new FTSs quick disconnect kit from Ss Brewtech is the perfect way to increase the efficiency of your cooling system while also making it easier to detach your fermenter's chiller coil for easy cleaning.
From: Ss Brewtech -
$4.95Floating Dip Tube FILTER For FermZilla or Kegmenter
Floating Dip Tube Filter
80 Mesh 304 Stainless - For FermZilla or Kegmenter.
Made from HDPE and 304 Grade stainless steel, this product can be boiled or sanitised in the full range of cleaners that we sell. The plastic HDPE is over moulded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning.
-
$5.00FermZilla Seal Kit (Lid O-ring, Collection Container O-ring and Cone O-Ring)
Replacement seal kit for the FermZilla 27L and 55L Conical Range
Lid O-ring Also suits the Fermzilla Flat Bottom and All Rounder (for Lid O-ring)
Out of Stock -
$15.00FermZilla - All Rounder 30L/60L Base Support Webbing / Strap / Bridle / Carry Tie Down
This handy little strap will make cleaning and transport your FermZilla All Rounder 30L or 60L an absolute breeze. Simply attach through both sections of the base in the orientation you wish. Slide up and out of the little buckle pieces making sure that the buckle is facing towards you, then strap in and strap down!
The Strap is long enough for the 60L FZ-AR and 30L. We recommend rolling up the excess strap and paper clipping or cutting to suit the 30L.Out of Stock -
$14.95FTSs Controller Mounting Bracket
A mounting bracket for Ss Brewtech fermenters. Mounts to the vessel's thermowell port for all Chronical fermenters and standard Brite Tanks, or to the tri-clamp bracket for Unitanks and Brewmaster Brite Tanks. - Custom tooled shelf for FTSs controllers - Thermowell Bracket is matte black - Tri-Clamp Bracket is 304 Stainless From: Ss Brewtech -
$12.9560cm Thermowell - 1/4inch Duotight Bulkhead Included
This thermowell fits into any 8mm Hole and can literally be installed into almost any fermenter lid.
-
$30.00Thermowell - Weldless, Multiple Sizes
A stainless steel thermowell for temperature probes. Designed for Ss Brew Tech products but the universal weldless design can be used with other fermenters.
- Brewer's Grade 304 Ss
- Installs into 17mm punched / drilled hole
- 6.5 mm inner diameter of tube openingAvailable in these sizes:
- 100mm
- 200mm
- 300mmIncludes one o-ring.
-
$29.95Blow Off Barb For FTSs and Ss Brew Bucket Lids
Blow Off Barb For FTSs and Ss Brew Bucket Lids.
- Custom tooled specifically for FTSs/Brew Bucket lids
- Fits into blow off / airlock hole
- 1/2" hose barb
- 304 Stainless construction
- Includes 1 spare o-ring (1 o-ring for use / 1 spare) -
$84.95Leg Extensions for Ss Chronical 52L and 64L Fermenters
Leg Extensions for Ss Brew Tech Chronical 52L and Chronical 64L fermenters.
- Made from 304 Stainless Steel
- Finish matches Chronical legs
- 3/8" male stem on top (insert to legs)
- 3/8" female on bottom (for casters/feet)
- Approx. 25cm (10") total lengthSold as a set of four.
Out of Stock
